now browsing by tag
[New Cisco Exam Dumps] Free Download 200-155 Dumps PDF Files, Latest Cisco 200-155 Dumps Youtube Demo
Latest Cisco CCNA Data Center 200-155 dumps exam questions and answers free update. Download Cisco CCNA Data Center 200-155 dumps pdf practice files and study guides to have a free try. https://www.leads4pass.com/200-155.html dumps pdf training materisls. The best Cisco CCNA Data Center 200-155 dumps pdf and vce training resources demo, 100% success and guarantee to pass Cisco 200-155 exam test easily.
Free latest Cisco 200-155 dumps pdf files download: https://drive.google.com/open?id=0B_7qiYkH83VROUdnZWRYLTJta1E
Free latest Cisco 200-150 dumps pdf files download: https://drive.google.com/open?id=0B_7qiYkH83VRNFFRMURQbmZ4T1U
A router has two Fast Ethernet interfaces and needs to connect to four VLANs in the local network. How can you accomplish this task, using the fewest physical interfaces and without decreasing network performance?
A. Use a hub to connect the four VLANS with a Fast Ethernet interface on the router.
B. Add a second router to handle the VLAN traffic.
C. Add two more Fast Ethernet interfaces.
D. Implement a router-on-a-stick configuration.
Correct Answer: D
Which of the following describes the roles of devices in a WAN? (Choose three.)
A. A CSU/DSU terminates a digital local loop.
B. A modem terminates a digital local loop.
C. A CSU/DSU terminates an analog local loop.
D. A modem terminates an analog local loop.
E. A router is commonly considered a DTE device.
F. A router is commonly considered a DCE device.
Correct Answer: ADE
A receiving host computes the checksum on a frame and determines that the frame is damaged. The frame is then discarded. 200-155 pdf At which OSI layer did this happen?
D. data link
Correct Answer: D
A network interface port has collision detection and carrier sensing enabled on a shared twisted pair network. 200-155 dumps From this statement, what is known about the network interface port?
A. This is a 10 Mb/s switch port.
B. This is a 100 Mb/s switch port.
C. This is an Ethernet port operating at half duplex.
D. This is an Ethernet port operating at full duplex.
E. This is a port on a network interface card in a PC.
Correct Answer: C
Where does routing occur within the DoD TCP/IP reference model?
Correct Answer: B
Which three statements accurately describe Layer 2 Ethernet switches? (Choose three.)
A. Spanning Tree Protocol allows switches to automatically share VLAN information.
B. Establishing VLANs increases the number of broadcast domains.
C. Switches that are configured with VLANs make forwarding decisions based on both Layer 2 and Layer 3 address information.
D. Microsegmentation decreases the number of collisions on the network.
E. In a properly functioning network with redundant switched paths, each switched segment will contain one root bridge with all its ports in the forwarding state. All other switches in that broadcast domain will have only one root port.
F. If a switch receives a frame for an unknown destination, it uses ARP to resolve the address.
Correct Answer: BDE
A network administrator is verifying the configuration of a newly installed host by establishing an FTP connection to a remote server. What is the highest layer of the protocol stack that the network administrator is using for this operation?
F. data link
Correct Answer: A
Which layer in the OSI reference model is responsible for determining the availability of the receiving program and checking to see if enough resources exist for that communication?
Correct Answer: E
For what two purposes does the Ethernet protocol use physical addresses? 200-155 dumps (Choose two.)
A. to uniquely identify devices at Layer 2
B. to allow communication with devices on a different network
C. to differentiate a Layer 2 frame from a Layer 3 packet
D. to establish a priority system to determine which device gets to transmit first
E. to allow communication between different devices on the same network
F. to allow detection of a remote device when its physical address is unknown
Correct Answer: AE
Which of the following correctly describe steps in the OSI data encapsulation process? (Choose two.)
A. The transport layer divides a data stream into segments and may add reliability and flow control information.
B. The data link layer adds physical source and destination addresses and an FCS to the segment.
C. Packets are created when the network layer encapsulates a frame with source and destination host addresses and protocol related control information.
D. Packets are created when the network layer adds Layer 3 addresses and control information to a segment.
E. The presentation layer translates bits into voltages for transmission across the physical link.
Correct Answer: AC
Reference: https://www.leads4pass.com/200-155.html dumps pdf questions and answers free update.